Tag: DTE

IP 500v2 Release 12
IP Office

Re-config IP500 w/DTE

The DTE port on the back of an IP Office Control Unit is not normally used when configuring an IP Office system. However the DTE port can be used to erase the system’s operational software and/or configuration if necessary.

Due to the drastic nature of these actions they should only be performed if absolutely necessary to return a system back to working order. In either case you must ensure that you have a backup copy of the system configuration.

Access to the DTE port requires a serial cable between your PC/Laptop and the IP Office (such as a standard modem cable).

read more
IP Office

IP office Debug Commands

IP Office AT-DEBUG Commands
Compiled by Kyle L Holladay, Sr. R.I.P.

CommandParameterDefinition
upgrade–Erase Code and Reboot/reload
reboot–Reboot
erasenvconfig–Erase NV config
eraseconfig–Erase config
qbf–Send Fox messages to WAN and MGR
call(service)Call the specified service
fecpram–List FCC parameter data
fecstats–List FCC traffic statistics
fecrmon–Enable/disable FCC RMON counters
fectrace–Enable/disable FCC debug tracing (needs debug build)
fecrestart–Restart FCC transmitter
pcmcia–Show current PCMCIA status
crc6–Display CRC-6 error count
ti–Send cmd to Ti/Telogy stack
atmcms–Dump status of CM ATM lines
atmcfg(lineid)Change configuration of an ATM trunk
atmdump(lineid)Dumps configuration of an ATM trunk
atmdiag(on|off)Turn on/off the ATM diagnostic logging
echo(on|off)Turn on/off the ATM Echo cancellation if enabled in configuration
atm4trunks–Dump status of ATM4U trunks
atm4lin(a|b|c|d)Show/change status of ATM4U lines
dspatver(a|b|c|d)Report version number of ATM4U card in Slot A/B
dspatmem(a|b|c|d)Read/Write to ATM4U card in Slot A/Bs DSP memory
dspathpi(a|b|c|d)Thrash or stop HPI accesses (to DSP) for ATM4U card in Slot A-D
atm4usc(a|b|c|d)Send Vinetic Short Command to ATM4U card in Slot A-D
atm4urmb(a|b|c|d)Read Vinetic Mailbox command from ATM4U card in Slot A-D
atm4uwmb(a|b|c|d)Write Vinetic Mailbox command to ATM4U card in Slot A-D
atm4ucram(a|b|c|d)Write Vinetic CRAM Data to ATM4U card in Slot A-D
atm4ulow(a|b|c|d)Set ATM4 Vinetic processor in low power mode in Slot A-D
atm4uhigh(a|b|c|d)Set ATM4 Vinetic processor in high power mode in Slot A-D
use_diag_cmd–use diag commands
conferdsp–Read current status of Conferencing DSP
conferdspmem–Read/Write to Conferencing DSP memory
conferdspch–Compare DSP Image words against what is stored in DSP memory
dspt1a/b–Read/Write to T1 card in Slot A/B’s DSP memory
switchdump–Dump all the registers on the Ethernet Switch
switchport–configure one of the PHY ports on the switch
switchread–Read a register on the Ethernet Switch
switchwrite–Write a register on the Ethernet Switch
vcmread–Read an SPI register on VCM ethernet switch
vcmwrite–Write an SPI register on VCM ethernet switch
vcmport–configure one of the PHY ports on the VCM switch
phydump–Dump all the registers from the PHY connected to the LAN2/WAN port
phyread–Read register from PHY
phywrite–Write register on PHY
lanstatus–Display the connection status of the external LAN/WAN links
gndstatus
reset
quiesce
rx
rxt
flush
cmd
token
features
speed		Perform G&D SmartCard commands (e.g. “gnd speed”)
briregs
dsp
isac
lock		Perform BRI commands (e.g. “bri dsp”)
priudspver
dspqueues
dsptrace
dspload
dspmem
dspmsgwr
dspmsgrd
dspstatus
alarmsim
egram		Display DSP version information
Display DSP message queue information
Enable/Disable DSP debug trace
Load and run DSP image
DSP memory edit
DSP message queue test write
DSP message queue test read
Print DSP statistics
Run alarm simulations
Receiver equalizer RAM modifications
DVPRDCMD
RDDATA
PAGE
PREAD
PWRITE
DREAD
DWRITE
REVCODE
MEMTEST
QSAPP
INIT
CLOSE
DOPTS
POPTS
DDATA
PDATA
CODEC
RING
DIAL
MWAIT
STATUS [C]
TEST
GAIN
POWERETR
LLC
REGS
PROF
DPL		read a command/control register
read a data register
select a memory page
perform a paged read
perform a paged write
perform a direct read
perform a direct write
read the revision code
perform a memory test
run the Legerity QuickStart application
initialise the subsystem
close down the subsystem
display device options
display port options
display device data
display port data
set the codec law for a port
cause a line to ring
dial a number
use the message waiting indicator
display status
runs a test on a port
set line gains
apply power to an ETR phone
execute a low-level command
dumps registers for a port
display a profile
set the DTE print level
ipstats–Dump IP/ICMP/TCP/UDP stats
ivm-help–Embedded Voicemail Commands
ivm-mbox-show–Show mailboxes
ivm-mbox-showShow contents of specified mailbox
ivm-mbox-clearClear specified mailbox
ivm-msg-delnnn dd/dd/dd hh:mm:ssDelete specified message
ivm-msg-del-all–Delete all voicemail messages
ivm-flash-del-all––
ivm-limits-max-nummsg-show––
ivm-limits-max-nummsg-setxxx–
ivm-limits-max-mstime-show––
ivm-limits-max-mstime-setxxx–
ivm-status-show––
ivm-monitor-toggle––
read more
IP Office

Set/Show IP address for IP Office

Although normally done from within the the Manager program, you can also display or change the IP adresss of either LAN port via the RS232 (DTE) Maintenance port on the back of the IP Office. They may be instances where this is useful.

DTE Port Settings:

  • Access to the DTE port requires a (straight) serial cable between your PC/Laptop and the IP Office.
  • Configure PuTTY, HyperTerminal, etc, for serial as follows: 38,400 – 8 – N – 1 – None – VT100

Procedure:

Enter the following commands (in bold) when the IPOffice is up and running:

at OK at-debug <IPOffice Manager Version 0.2> Wed 26/2/2014 10:27:58, Hello>updatelanCurrent LAN1: ipaddr: 192.168.42.1 mask: 255.255.255.0 (LAN port) Current LAN2: ipaddr: 128.75.0.100 mask: 255.255.255.0 (WAN port) Enter which lan interface (lan1 or lan2): lan1 (or hit enter to leave unchanged)Enter IP address (a.b.c.d): 10.10.10.1Enter IP mask (a.b.c.d): 255.255.255.0Add default gateway (yes or no)? 10.10.10.254 Start WriteConfig at f7e0969c, savemode SaveNormal, writetype ToFlash Start WriteConfig at f7e0969c, savemode SaveNormal, writetype ToFile : :Configuration has been saved. Reboot now (yes or no)? no (enter to 'yes' to reboot system immediately)Issue the 'reboot' command later. Wed 26/2/2014 10:28:51, Hello>

read more
IP Office

Reset Security Passwords in IP Office

Passwords can be reset to default values via the RS232 (DTE) Maintenance port on the back of the IP Office.

DTE Port Settings:

  • Access to the DTE port requires a (straight) serial cable between your PC/Laptop and the IP Office.
  • Configure PuTTY, HyperTerminal, etc, for serial as follows: 38,400 – 8 – N – 1 – None – VT100

Procedure:

Enter the following commands (in bold) when the IPOffice is running normally. (Do no press ESC during startup!):

read more
IP Office

DTE Port Programming

This procedure will allow you to reconfigure an Avaya IP Office back to factory defaults if you don’t know the units IP Address or password using the DTE serial port on the back of an IP Office Control Unit.

Overview

The DTE port on the back of an IP Office Control Unit is not normally used when configuring an IP Office system. However the DTE port can be used to erase the system’s operational software and/or configuration if necessary.

Due to the drastic nature of these actions they should only be performed if absolutely necessary to return a system back to working order. In either case you must ensure that you have a backup copy of the system configuration.

read more