IP Office AT-DEBUG Commands
Compiled by Kyle L Holladay, Sr. R.I.P.
| Command | Parameter | Definition |
| upgrade | – | Erase Code and Reboot/reload |
| reboot | – | Reboot |
| erasenvconfig | – | Erase NV config |
| eraseconfig | – | Erase config |
| qbf | – | Send Fox messages to WAN and MGR |
| call | (service) | Call the specified service |
| fecpram | – | List FCC parameter data |
| fecstats | – | List FCC traffic statistics |
| fecrmon | – | Enable/disable FCC RMON counters |
| fectrace | – | Enable/disable FCC debug tracing (needs debug build) |
| fecrestart | – | Restart FCC transmitter |
| pcmcia | – | Show current PCMCIA status |
| crc6 | – | Display CRC-6 error count |
| ti | – | Send cmd to Ti/Telogy stack |
| atmcms | – | Dump status of CM ATM lines |
| atmcfg | (lineid) | Change configuration of an ATM trunk |
| atmdump | (lineid) | Dumps configuration of an ATM trunk |
| atmdiag | (on|off) | Turn on/off the ATM diagnostic logging |
| echo | (on|off) | Turn on/off the ATM Echo cancellation if enabled in configuration |
| atm4trunks | – | Dump status of ATM4U trunks |
| atm4lin | (a|b|c|d) | Show/change status of ATM4U lines |
| dspatver | (a|b|c|d) | Report version number of ATM4U card in Slot A/B |
| dspatmem | (a|b|c|d) | Read/Write to ATM4U card in Slot A/Bs DSP memory |
| dspathpi | (a|b|c|d) | Thrash or stop HPI accesses (to DSP) for ATM4U card in Slot A-D |
| atm4usc | (a|b|c|d) | Send Vinetic Short Command to ATM4U card in Slot A-D |
| atm4urmb | (a|b|c|d) | Read Vinetic Mailbox command from ATM4U card in Slot A-D |
| atm4uwmb | (a|b|c|d) | Write Vinetic Mailbox command to ATM4U card in Slot A-D |
| atm4ucram | (a|b|c|d) | Write Vinetic CRAM Data to ATM4U card in Slot A-D |
| atm4ulow | (a|b|c|d) | Set ATM4 Vinetic processor in low power mode in Slot A-D |
| atm4uhigh | (a|b|c|d) | Set ATM4 Vinetic processor in high power mode in Slot A-D |
| use_diag_cmd | – | use diag commands |
| conferdsp | – | Read current status of Conferencing DSP |
| conferdspmem | – | Read/Write to Conferencing DSP memory |
| conferdspch | – | Compare DSP Image words against what is stored in DSP memory |
| dspt1a/b | – | Read/Write to T1 card in Slot A/B’s DSP memory |
| switchdump | – | Dump all the registers on the Ethernet Switch |
| switchport | – | configure one of the PHY ports on the switch |
| switchread | – | Read a register on the Ethernet Switch |
| switchwrite | – | Write a register on the Ethernet Switch |
| vcmread | – | Read an SPI register on VCM ethernet switch |
| vcmwrite | – | Write an SPI register on VCM ethernet switch |
| vcmport | – | configure one of the PHY ports on the VCM switch |
| phydump | – | Dump all the registers from the PHY connected to the LAN2/WAN port |
| phyread | – | Read register from PHY |
| phywrite | – | Write register on PHY |
| lanstatus | – | Display the connection status of the external LAN/WAN links |
| gnd | status reset quiesce rx rxt flush cmd token features speed | Perform G&D SmartCard commands (e.g. “gnd speed”) |
| bri | regs dsp isac lock | Perform BRI commands (e.g. “bri dsp”) |
| priu | dspver dspqueues dsptrace dspload dspmem dspmsgwr dspmsgrd dspstatus alarmsim egram | Display DSP version information Display DSP message queue information Enable/Disable DSP debug trace Load and run DSP image DSP memory edit DSP message queue test write DSP message queue test read Print DSP statistics Run alarm simulations Receiver equalizer RAM modifications |
| DVP | RDCMD RDDATA PAGE PREAD PWRITE DREAD DWRITE REVCODE MEMTEST QSAPP INIT CLOSE DOPTS POPTS DDATA PDATA CODEC RING DIAL MWAIT STATUS [C] TEST GAIN POWERETR LLC REGS PROF DPL | read a command/control register read a data register select a memory page perform a paged read perform a paged write perform a direct read perform a direct write read the revision code perform a memory test run the Legerity QuickStart application initialise the subsystem close down the subsystem display device options display port options display device data display port data set the codec law for a port cause a line to ring dial a number use the message waiting indicator display status runs a test on a port set line gains apply power to an ETR phone execute a low-level command dumps registers for a port display a profile set the DTE print level |
| ipstats | – | Dump IP/ICMP/TCP/UDP stats |
| ivm-help | – | Embedded Voicemail Commands |
| ivm-mbox-show | – | Show mailboxes |
| ivm-mbox-show | nnn | Show contents of specified mailbox |
| ivm-mbox-clear | nnn | Clear specified mailbox |
| ivm-msg-del | nnn dd/dd/dd hh:mm:ss | Delete specified message |
| ivm-msg-del-all | – | Delete all voicemail messages |
| ivm-flash-del-all | – | – |
| ivm-limits-max-nummsg-show | – | – |
| ivm-limits-max-nummsg-set | xxx | – |
| ivm-limits-max-mstime-show | – | – |
| ivm-limits-max-mstime-set | xxx | – |
| ivm-status-show | – | – |
| ivm-monitor-toggle | – | – |
Discover more from IP Office Assistance
Subscribe to get the latest posts sent to your email.